11.6 Inch 1920x1080 Tft Lcd All Viewing Angle 30 Pin Edp 220 Nit
General Description:
The manufacturer of M116B30-040-121-0102 is BOE. The display mode is Normally black. The contrast ratio is 1000:1, the color saturation is 72%NTSC, the response time is 25 ms, the optimal viewing Angle is symmetrical, the operating temperature is 0℃ to +50℃, and the storage temperature is -10℃ to +60℃.
Specifications:
| Parameter |
Specification |
Unit |
Note |
| Display size |
11.6” (Diagonal) |
inch |
|
| Active area |
256.32(H) ×144 . 18(V) |
mm |
|
| Pixel Format |
1920(H) ×1080(V) (1pixel = R + G + B dot) |
pixel |
|
| Pixel pitch |
0.1335(H) x 0.1335 (V) |
mm |
|
| Pixel configuration |
R, G, B vertical stripe |
|
|
| Display mode |
Normally black |
|
|
|
Surface treatment of front polarizer
|
Anti-glare coating: (3H) |
|
|
Interface Connection:
| Pin No. |
Symbol |
I/O |
Function |
Remark |
| 1 |
CABC_EN / NC |
- |
Reserved for CD |
[Note1] |
| 2 |
H_GND |
P |
High Speed round |
[Note2] |
| 3 |
Lane1_N |
I |
Complement Signal Link Lane 1 |
|
| 4 |
Lane1_P |
I |
True Signal Link Lane 1 |
|
| 5 |
H_GND |
P |
High Speed round |
[Note2] |
| 6 |
Lane0_N |
I |
Complement Signal Link Lane 0 |
|
| 7 |
Lane0_P |
I |
True Signal Link Lane 0 |
|
| 8 |
H_GND |
P |
High Speed round |
[Note2] |
| 9 |
AUX_CH_P |
I |
True Signal Auxiliary Channel |
|
| 10 |
AUX_CH_N |
I |
Complement Signal Auxiliary Channel |
|
| 11 |
H_GND |
P |
High Speed round |
[Note2] |
| 12 |
LCD_VDD |
P |
LCD logic and driver power(3.3V) |
|
| 13 |
LCD_VDD |
P |
LCD logic and driver power(3.3V) |
|
| 14 |
NC |
I |
Reserved for LCD manufacturer’s use |
[Note1] |
| 15 |
LCD_GND |
P |
LCD logic and driver ground |
|
| 16 |
LCD_GND |
P |
LCD logic and driver ground |
|
| 17 |
HPD |
O |
HPD signal pin |
|
| 18 |
LED-1 |
P |
Backlight ground |
|
| 19 |
LED-2 |
P |
Backlight ground |
|
| 20 |
LED-3 |
P |
Backlight ground |
|
| 21 |
LED-4 |
P |
Backlight ground |
|
| 22 |
BL_ENABLE |
I |
Backlight on/off |
|
| 23 |
BL_PWM_DIM |
I |
System PWM |
|
| 24 |
SCL/NC |
- |
Reserved for LCD manufacturer’s use |
[Note1] |
| 25 |
SDA/NC |
- |
Reserved for LCD manufacturer’s use |
[Note1] |
| 26 |
BL_PWR |
P |
Backlight power |
|
| 27 |
BL_PWR |
P |
Backlight power |
|
| 28 |
BL_PWR |
P |
Backlight power |
|
| 29 |
BL_PWR |
P |
Backlight power |
|
| 30 |
NC |
- |
Reserved for LCD manufacturer’s use |
[Note1] |
CN1 (eDP signals , +3.3V DC power supply and B/L power supply)
[Note1] Don’t input any signals or any powers into a NC pin. Keep the NC pin open.
[Note2] The shielding case is connected with signal GND.Connector used :20455-030E-76(I-PEX),Corresponding connector : 20453-030T (I-PEX)
Absolute Maximum Ratings:
| Parameter |
Symbol |
Condition |
Ratings |
Unit |
Remark |
| MIN |
MAX |
| +3.3V supply voltage |
VDD |
Ta=25℃ |
-0.3 |
+3.6 |
V |
|
| Backlight supply voltage |
VBL |
Ta=25℃ |
-0.3 |
+21 |
V |
|
| Input voltage(eDP) |
VI |
Ta=25℃ |
-0.3 |
+1.5 |
V |
|
| Input voltage(BL) |
VBL_I |
Ta=25℃ |
-0.3 |
VDD+0.3 |
V |
|
| Storage temperature |
Tstg |
|
-10 |
+60 |
℃ |
|
| Operation temperature |
Topa |
|
0 |
+50 |
℃ |
“Absolute Maximum Ratings” is regulations that do not exceed it even momentarily.
Stress beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.
Backlight Driving:
The backlight system is an edge-lighting type with white-LED.
(It is usually required to measure under the following condition: Ta=25C±2C)
| Parameter |
Symbol |
Min. |
Typ. |
Max. |
Unit |
Remark |
| Supply voltage |
VBL |
7.0 |
12.0 |
21.0 |
V |
|
|
Current dissipation
|
IBL
|
-
|
(227) |
(251) |
mA |
VBL=12V Duty Ratio=100% |
| |
(135) |
(135) |
mA |
VBL=7.9V Duty Ratio=40% |
| Modulated light signal voltage |
VPWM H |
1.85 |
- |
VDD |
V |
|
| VPWM L |
0 |
- |
0.7 |
V |
|
| Brightness Control Duty Ratio |
Duty |
1 |
- |
100 |
% |
|
| Brightness Control pulse width |
TPWM |
5 |
- |
- |
ps |
|
| Brightness Control frequency |
PWM |
200 |
- |
2,000 |
Hz |
|
| LED-BL ON/OFF High voltage |
VCNT H |
1.8 |
3.3 |
3.6 |
V |
|
Optical Specification:
| Paramete |
Conditions |
Min. |
Typ. |
Max. |
Unit |
|
Viewing Angle(CR>10)
|
Horizontal |
L |
- |
89 |
- |
degree
|
| R |
- |
89 |
- |
| Vertical |
T |
- |
89 |
- |
| B |
- |
89 |
- |
| Contrast Ratio |
Center |
700 |
1000 |
- |
- |
| Response Time |
Tr+Td |
- |
25 |
|
ms |
|
CF Color Chromaticity(CIE1931)
|
Red x |
Typ.
-0.05
|
TBD |
Typ. +0.05
|
- |
| Red y |
TBD |
- |
| Green x |
TBD |
- |
| Green y |
TBD |
- |
| Blue x |
TBD |
- |
| Blue y |
TBD |
- |
| White x |
(0.313) |
- |
| White y |
(0.329) |
- |
| NTSC ratio |
% |
|
(72) |
|
- |
| Luminance of white |
YLI |
|
220 |
|
cd/m |
Handling Precautions:
1.Liquid crystal contained in the panel may leak if the LCD is broken. Rinse it as soon as possible if it gets inside your eye or mouth by mistake.
2.If a minute particle enters in the module and adheres to an optical material, it may cause display non-uniformity issue, etc. Therefore, fine-pitch filters have to be installed to cooling and inhalation hole if you intend to install a fan.
3.Do not expose the LCD module to a direct sunlight, for a long period of time to protect the module from the ultra violet ray.
Reliability Test Items:
| No. |
Test Item |
Conditions |
| 1 |
High temperature storage test |
Ta=60℃ 72h |
| 2 |
Low temperature storage test |
Ta=-10℃ 72h |
| 3 |
High temperature
& high humidity operation test
|
Ta=40℃90%RH 72h
(No condensation)
|
| 4 |
High temperature operation test |
Ta=50℃ 72h |
| 5 |
Low temperature operation test |
Ta=0℃ 72h |
Product Tags:
|
|
30 Pin Edp TFT HD Display Anti Glare 11.6 Inch LCD 1920x1080 All Viewing Angle 220 Nit Images
|
